HDD жёсткий диск Samsung HD253GJ 250 Гб

БУ, работает, самодиагностику прошёл.

🔍 Анализ SMART для Samsung HD253GJ (250 GB)

✅ Краткий вердикт: Диск в хорошем состоянии

Все критические параметры в норме, угроз потери данных на данный момент нет.

📊 Детальный разбор ключевых атрибутов

5 Reallocated_Sector_Ct 0 ✅ Отлично Нет переназначенных секторов

197 Current_Pending_Sector 0 ✅ Отлично Нет нестабильных секторов

198 Offline_Uncorrectable 0 ✅ Отлично Нет нечитаемых секторов

199 UDMA_CRC_Error_Count 1 ⚠️ Незначительно Единичная ошибка шины, скорее всего, разовый сбой кабеля/контакта

1 Raw_Read_Error_Rate 8 ✅ Норма Для дисков Samsung сырое значение не критично, нормализованное VALUE=100 > THRESH=51

200 Multi_Zone_Error_Rate 792 ✅ Норма Специфичный атрибут Samsung, но VALUE=100 — в пределах спецификации

194 Temperature_Celsius 37°C ✅ Отлично Рабочая температура в безопасном диапазоне (мин/макс: 18/46)

📈 Общая статистика эксплуатации

Наработка: 15 375 часов (~1.75 года непрерывной работы или 4-6 лет обычного использования)

Включений: 3 049 раз

Циклов питания: 3 098 раз

Скорость вращения: 7200 RPM

Ошибки в логе: Не зафиксировано

smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-117-generic] (local build)

Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

# sudo smartctl -a /dev/sdc

smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-117-generic] (local build)

Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===

Device Model: SAMSUNG HD253GJ

Serial Number: S24JJ9FZB00578

LU WWN Device Id: 5 0024e9 203cef435

Firmware Version: 1AJ10001

User Capacity: 250 059 350 016 bytes [250 GB]

Sector Size: 512 bytes logical/physical

Rotation Rate: 7200 rpm

Form Factor: 3.5 inches

Device is: Not in smartctl database 7.3/5528

ATA Version is: ATA8-ACS T13/1699-D revision 6

SATA Version is: SATA 2.6, 3.0 Gb/s

Local Time is: Sun May 24 11:06:52 2026 +07

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

General SMART Values:

Offline data collection status: (0x00) Offline data collection activity

was never started.

Auto Offline Data Collection: Disabled.

Self-test execution status: ( 0) The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: ( 2280) seconds.

Offline data collection

capabilities: (0x5b) SMART execute Offline immediate.

Auto Offline data collection on/off support.

Suspend Offline collection upon new

command.

Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

Selective Self-test supported.

SMART capabilities: (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability: (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time: ( 2) minutes.

Extended self-test routine

recommended polling time: ( 38) minutes.

SCT capabilities: (0x003f) SCT Status supported.

SCT Error Recovery Control supported.

SCT Feature Control supported.

SCT Data Table supported.

SMART Attributes Data Structure revision number: 16

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE

1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 8

2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0

3 Spin_Up_Time 0x0023 084 083 025 Pre-fail Always - 5006

4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 3049

5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0

7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0

8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0

9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 15375

10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0

11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0

12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3098

191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 10

192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0

194 Temperature_Celsius 0x0002 063 054 000 Old_age Always - 37 (Min/Max 18/46)

195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0

196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0

197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0

198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0

199 UDMA_CRC_Error_Count 0x0036 100 100 000 Old_age Always - 1

200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 792

223 Load_Retry_Count 0x0032 252 252 000 Old_age Always - 0

225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 3108

SMART Error Log Version: 1

No Errors Logged

SMART Self-test log structure revision number 1

No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 0

Note: revision number not 1 implies that no selective self-test has ever been run

SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS

1 0 0 Completed [00% left] (0-65535)

2 0 0 Not_testing

3 0 0 Not_testing

4 0 0 Not_testing

5 0 0 Not_testing

Selective self-test flags (0x0):

After scanning selected spans, do NOT read-scan remainder of disk.

If Selective self-test is pending on power-up, resume after 0 minute delay.

The above only provides legacy SMART information - try 'smartctl -x' for more